Studies on the SPEEK membrane with low degree of sulfonation as a stable proton exchange membrane for fuel cell applications

Document Type: Research Paper

Authors

1 School of Chemical Engineering, Iran University of Science and Technology, Narmak, Tehran 16846-13114, Iran

2 Green Research Center (GRC) & School of Chemical Engineering (SChE) Iran University of Science & Technology

Abstract

Sulfonated poly (ether ether ketone) (SPEEK) with a low degree of sulfonation (DS = 40%) was prepared for proton exchange membrane fuel cells (PEMFC). Poly (ether ether ketone) (PEEK) was sulfonated in concentrated H2SO4 under N2 atmosphere and characterized by the hydrogen nuclear magnetic resonance (H-NMR) technique. After preparation of the SPEEK polymer, the obtained polymer was dissolved in dimethylacetamide (DMAC) solvent and then the solution casting method was applied for the fabrication of membranes. Water uptake behavior, ion exchange capacity (IEC), and the proton conductivity at different temperatures and different relative humidity were determined and compared with a commercial Nafion 117 membrane. The IEC and the proton conductivity results showed that the sulfonation process successfully created   proton conduction channels. In addition, the thermal, mechanical, chemical, and hydrolytic stabilities were thoroughly investigated for the prepared membrane. The low degree of sulfonation SPEEK showed a desirable chemical durability with a higher dimensional, mechanical, and thermal stability than Nafion-117 but lower water uptake and proton conductivity.

Keywords

Main Subjects


[1] Ouyang L., Zhao Y., Jin G., Lu T., Li J., Qiao Y., et al., "Influence of sulfur content on bone formation and antibacterial ability of sulfonated PEEK", Biomaterials 2016, 83:115..

 

[2] Montero J.F.D., Tajiri H.A., Barra G.O., Fredel M.C., Benfatti C.A.M., Magini R.S., et al. "Biofilm behavior on sulfonated poly(ether-ether-ketone) (sPEEK)", Materials Science and Engineering C. 2017, 70:456.

 

[3] Montero J.F., Barbosa L.C., Pereira U.A., Barra G.M., Fredel M.C., Benfatti C.A., et al. "Chemical, microscopic, and microbiological analysis of a functionalized poly-ether-ether-ketone-embedding antibiofilm compounds", Journal of Biomedical Materials Research Part A. 2016, 104:3015.

 

[4] Zhuang Z., Qi D., Zhao C., Na H. "A novel highly sensitive humidity sensor derived from sulfonated poly(ether ether ketone) with metal salts-ion substitution", Sensors and Actuators B. 2016, 236:701.

 

[5] Zhuang Z., Li Y., Qi D., Zhao C., Na H. "Novel polymeric humidity sensors based on sulfonated poly (ether ether ketone) s: Influence of sulfonation degree on sensing properties", Sensors and Actuators B: Chemical. 2016, 242: 801.

 

[6] Tang Y., Xue Z., Xie X., Zhou X. "Ionic polymer–metal composite actuator based on sulfonated poly(ether ether ketone) with different degrees of sulfonation", Sensors and Actuators A. 2016, 238:167.

 

[7] Morizur V., Hector D., Olivero S., Desmurs J.R., Duñach E. "Metal Sulfonate Polymers as Catalysts for the Heterogeneous Acylation of Aromatic Derivatives", European Journal of Organic Chemistry. 2016, 2016:3126 .

 

[8] Shi Y., Yoonessi M., Weiss R.A. "High Temperature Shape Memory Polymers", Macromolecules. 2013, 46:4160.

 

[9] Azher H., Scholes C., Kanehashi S., Stevens G., Kentish S. "The effect of temperature on the permeation properties of Sulphonated Poly (Ether Ether) Ketone in wet flue gas streams", Journal of Membrane Science. 2016, 519:55.

 

[10] Xin Q., Zhang Y., Shi Y., Ye H., Lin L., Ding X., et al. "Tuning the performance of CO2 separation membranes by incorporating multifunctional modified silica microspheres into polymer matrix", Journal of Membrane Science. 2016, 514:73.

 

[11] Kwon S.H., Rhim J.W. "Study on Acid/Base Formation by Using Sulfonated Polyether Ether Ketone/Aminated Polysulfone Bipolar Membranes in Water Splitting Electrodialysis", Industrial & Engineering Chemistry Research. 2016, 55:2128.

 

[12] Dai J., Teng X., Song Y., Jiang X., Yin G. "A super thin polytetrafluoroethylene/sulfonated poly(ether ether ketone) membrane with 91% energy efficiency and high stability for vanadium redox flow battery", Journal of Applied Polymer Science. 2016, 133:43593.

 

[13] Gong C., Zheng X., Liu H., Wang G., Cheng F., Zheng G., et al. "A new strategy for designing high-performance sulfonated poly(ether ether ketone) polymer electrolyte membranes using inorganic proton conductor-functionalized carbon nanotubes", Journal of Power Sources 2016, 325:453.

 

[14] Sadrjahani M., Gharehaghaji A.A., Javanbakht M. "Aligned Electrospun Sulfonated Polyetheretherketone Nanofiber Based Proton Exchange Membranes for Fuel Cell Applications", Polymer Engineering and Science. 2016.

 

[15] Yin Y.H., Wang H.Y., Cao L., Li Z., Li Z.Y., Gang M.Y., et al. "Sulfonated poly(ether ether ketone)-based hybrid membranes containing graphene oxide with acid-base pairs for direct methanol fuel cells", Electrochimica Acta. 2016, 203:178.

 

[16] He S., Lin Y., Ma H., Jia H., Liu X., Lin J. "Preparation of sulfonated poly(ether ether ketone) (SPEEK) membrane using ethanol/water mixed solvent". Materials Letters. 2016, 169:69.

 

[17] Deuk Ju Kim C.H.P., Sang Yong Nam. "Characterization of a soluble poly(ether ether ketone) anion exchange membrane for fuel cell application", International Journal of Hydrogen Energy. 2016, 41:7649.

 

[18] Elangovan M., Dharmalingam S. "Scaleup Suitability of Sulfonated Polyether Ether Ketone Membrane-Based Microbial Fuel Cell", Environmental Progress & Sustainable Energy. 2016, 35:80.

 

[19] Moreno N.G., Molina M.C., Gervasio D., Robles J.F.P. "Approaches to polymer electrolyte membrane fuel cells (PEMFCs) and their cost', Renewable and Sustainable Energy Reviews. 2015, 52:897.

 

[20] Wang J. "Barriers of scaling-up fuel cells: Cost, durability and reliability", Energy. 2015, 80:509.

 

[21] Chandan A., Hattenberger M., El-kharouf A., Du S., Dhir A., Self V., et al. "High temperature (HT) polymer electrolyte membrane fuel cells (PEMFC) A review", Journal of Power Sources. 2013, 231:264.

 

[22] Li G., Zhao C., Cui Y., Rong T., Zhu C., Na H. "Intermolecular ionic cross-linked sulfonated poly(ether ether ketone) membranes with excellent mechanical properties and selectivity for direct methanol fuel cells", RSC Advances 2016,  6:23025.

 

[23] Iulianelli A., Basile A. "Sulfonated PEEK-based polymers in PEMFC and DMFC applications: A review", International Journal of Hydrogen Energy. 2012, 37:15241.  

 

[24] Kreuer K.D. "On the development of proton conducting polymer membranes for hydrogen and methanol fuel cells", Journal of Membrane Science. 2001, 185:29.

 

[25] Smitha B., Sridhar S., Khan A.A. "Solid polymer electrolyte membranes for fuel cell applications—a review", Journal of Membrane Science. 2005, 259:10.

[26] Gebel Gr. "Structure of Membranes for Fuel Cells: SANS and SAXS Analyses of Sulfonated PEEK Membranes and Solutions", Macromolecules. 2013, 46:6057.

 

[27] Portale G., Carbone A., Martinelli A., Passalacqua E. Microstructure, "state of water and proton conductivity of sulfonated poly(ether ether ketone)", Solid State Ionics. 2013, 252:62.

 

[28] Ayyaru S., Dharmalingam S. "Development of MFC using sulphonated polyether ether ketone (SPEEK) membrane for electricity generation from waste water", Bioresource Technology. 2011, 102:11167.

 

[29] Ilbeygi H., Ghasemi M., Emadzadeh D., Ismail A.F., Zaidi S.M.J., Aljlil S.A., et al. "Power generation and wastewater treatment using a novel SPEEK nanocomposite membrane in a dual chamber microbial fuel cell", International Journal of Hydrogen Energy. 2015, 40:477.

 

[30] Krishnan P., Park J-S., Yang T-H., Lee W-Y., Kim C-S. "Sulfonated poly(ether ether ketone)-based composite membrane for polymer electrolyte membrane fuel cells", Journal of Power Sources. 2006, 163:2.

 

[31] Shin D.W., Kang N.R., Lee K.H., Cho D.H., Kim J.H., Lee W.H., et al. "Proton conducting, composite sulfonated polymer membrane for medium temperature and low relative humidity fuel cells", Journal of Power Sources. 2014, 262:162.

 

[32] Wang J., Bai H., Zhang H., Zhao L., Chen H., Li Y. "Anhydrous proton exchange membrane of sulfonated poly (ether ether ketone) enabled by polydopamine-modified silica nanoparticles", Electrochimica Acta. 2015, 152:443.

 

[33] Ma C., Zhang L., Mukerjee S., Ofer D., Nair B. "An investigation of proton conduction in select PEM’s and reaction layer interfaces-designed for elevated temperature operation" Journal of Membrane Science. 2003, 219:123.

 

[34] Doğan H., Inan T.Y., Unveren E., Kaya M. "Effect of cesium salt of tungstophosphoric acid (Cs-TPA) on the properties of sulfonated polyether ether ketone (SPEEK) composite membranes for fuel cell applications", international journal of hydrogen energy. 2010, 35:7784.

 

[35] Robertson G.P., Mikhailenko S.D., Wang K., Xing P., Guiver M.D., Kaliaguine S. "Casting solvent interactions with sulfonated poly(ether ether ketone) during proton exchange membrane fabrication", Journal of Membrane Science. 2003, 219:113.

 

[36] Gong C., Zheng X., Liu H., Wang G., Cheng F., Zheng G., et al. "A new strategy for designing high-performance sulfonated poly(ether ether ketone) polymer electrolyte membranes using inorganic proton conductor-functionalized carbon nanotubes", Journal of Power Sources. 2016, 325:453.

 

[37] Rangasamy V.S., Thayumanasundaram S, Greef ND, Seo JW, Locquet J-P. "Preparation and characterization of composite membranes based on sulfonated PEEK and AlPO4 for PEMFCs", Solid State Ionics. 2012, 216:83.

 

[38] Reyna-Valencia A., Kaliaguine S., Bousmina M. "Tensile Mechanical Properties of Sulfonated Poly(Ether Ether Ketone) (SPEEK) and BPO4/SPEEK Membranes", Journal of Applied Polymer Science. 2005, 98:2380.

 

[39] Takimoto N., Wu L., Ohira A,, Takeoka Y., Rikukawa M. "Hydration behavior of perfluorinated and hydrocarbon-type proton exchange membranes: Relationship between morphology and proton conduction", Polymer. 2009, 50:534.

 

[40] Huang RYM., Shao P., Burns C.M., Feng X. "Sulfonation of Poly(Ether Ether Ketone)(PEEK): Kinetic Study and Characterization", Journal of Applied Polymer Science. 2001, 82:2651.

 

[41] Yang ACC., Narimani R., Frisken B.J., Holdcroft S. "Investigations of crystallinity and chain entanglement on sorption and conductivity of proton exchange membranes", Journal of Membrane Science. 2014, 469:251.

 

[42] Vona MLD., Licoccia S., Knauth P. "Organic–inorganic hybrid membranes based on sulfonated polyaryl–ether–ketones: Correlation between water uptake and electrical conductivity", Solid State Ionics. 2008, 179:1161.

 

[43] Narducci R., Vona MLD., Knauth P. "Cation-conducting ionomers made by ion exchange of sulfonated poly-ether-ether-ketone: Hydration, mechanical and thermal properties and ionic conductivity", Journal of Membrane Science 2014, 465 185.

 

[44] Park C.H., Lee C.H., Guivera M.D., Lee Y.M. "Sulfonated hydrocarbon membranes for medium-temperature and low-humidity proton exchange membrane fuel cells (PEMFCs)}, Progress in Polymer Science. 2011, 36:1443.

 

[45] Gupta D., Choudhary V. "Studies on novel heat treated sulfonated poly (ether ether ketone)[SPEEK]/diol membranes for fuel cell applications", international journal of hydrogen energy. 2011, 36:8525.

 

[46] Wu H., Cao Y., Li Z., He G., Jiang Z. "Novel sulfonated poly (ether ether ketone)/phosphonic acid-functionalized titania nanohybrid membrane by an in situ method for direct methanol fuel cells",  Journal of Power Sources. 2015, 273:544.

 

[47] Leong J.X, Daud WRW., Ghasemi M., Ahmad A., Ismail M., Liew K.B. "Composite membrane containing graphene oxide in sulfonated polyether ether ketone in microbial fuel cell applications", International Journal of Hydrogen Energy. 2015, 40:11604.

 

[48] Knauth P., Vona MLD. "Sulfonated aromatic ionomers: Analysis of proton conductivity and proton mobility", Solid State Ionics. 2012, 225:255.

 

[49] Hongying Hou MLDV., Philippe Knauth. "Durability of Sulfonated Aromatic Polymers for Proton-Exchange-Membrane Fuel Cells". ChemSusChem. 2011, 4:1526.

 

[50] Perrot C., Gonon L., Marestin C., Morinb A., Gebel G. "Aging mechanism of Sulfonated poly(aryl ether ketone) (sPAEK) in an hydroperoxide solution and in fuel cell", Journal of Power Sources. 2010, 195:493.

 

[51] Kitiya Hongsirikarn XM., James G. Goodwin Jr., Stephen Creager. "Effect of H2O2 on Nafion® properties and conductivity at fuel cell conditions", Journal of Power Sources. 2011, 196:3060.

 

[52] Yue Z., Cai Y-B., Xu S. "Proton conducting sulfonated poly (imide-benzimidazole) with tunable density of covalent/ionic cross-linking for fuel cell membranes", Journal of Power Sources. 2015, 286:571.

 

[53] Jalani NH., Datta R. "The effect of equivalent weight, temperature, cationic forms, sorbates, and nanoinorganic additives on the sorption behavior of Nafion®", Journal of membrane science. 2005, 264:167.

 

[54] Meyer G., Perrot C., Gebel G., Gonon L., Morlat S., Gardette J-L. "Ex situ hydrolytic degradation of sulfonated polyimide membranes for fuel cells", Polymer 2006, 47:5003.

 

[55] Kusoglu A., Calabrese M., Z.Weber A. "Effect of Mechanical Compression on Chemical Degradation of NafionMembrane", ECS Electrochemistry Letters. 2014, 3:F33.