Study of the forming process effects on the wrinkling and thinning percentage of the micro-channels with serpentine layout

Document Type : Research Paper

Authors

1 university of kashan, kashan, iran

2 Faculty of Mechanical Engineering, Tarbiat Modares University

3 Fuel Cell Technology Research Laboratory, Malek Ashtar University of Technology

Abstract

In the present study, the lubricated and non-lubricated stamping processes are used for fabrication of the metallic bipolar plates (MBPPs) with a thickness of 0.1 mm made of SS3316 with a serpentine flow field. Experimental tests together with the finite element (FE) model are utilized to define the directional thickness distribution. According to the results, considering the friction factor of 0.1 during the FE analysis is capable of providing accurate results in terms of thickness prediction under lubricated conditions. The largest thinning percentages in the modified conditions are found to be 27.02%, 30.40%, and 26.00% in the longitudinal, diagonal, and transverse directions, respectively, indicating that the diagonal direction is the most critical one. Finally, the effect of lubricating condition on wrinkling of the sample is investigated. According to the results, using the lubricated condition during the stamping process would lead to augmentation of the wrinkling of the bipolar plate and also, the wrinkling of bipolar plate’s margin was not symmetrical.

Keywords


[1] S. Mahabunphachai, A Hybrid Hydroforming and Mechanical Bonding Process for Fuel Cell Biopolar Plates, 2008.
[2] A. Kirubakaran, S. Jain, R. Nema, A review on fuel cell technologies and power electronic interface, Renewable and sustainable energy reviews, 13(9) (2009) 2430-2440.
[3] V. Mehta, J.S. Cooper, Review and analysis of PEM fuel cell design and manufacturing, Journal of power sources, 114(1) (2003) 32-53.
[4] A. Manso, F. Marzo, J. Barranco, X. Garikano, M.G. Mujika, Influence of geometric parameters of the flow fields on the performance of a PEM fuel cell. A review, International journal of hydrogen energy, 37(20) (2012) 15256-15287.
[5] O.A. Alo, I.O. Otunniyi, H. Pienaar, Manufacturing methods for metallic bipolar plates for polymer electrolyte membrane fuel cell, Materials and Manufacturing Processes, 34(8) (2019) 927-955.
[6] S. Xu, K. Li, Y. Wei, W. Jiang, Numerical investigation of formed residual stresses and the thickness of stainless steel bipolar plate in PEMFC, International Journal of Hydrogen Energy, 41(16) (2016) 6855-6863.
 
[7] R. Zhang, S. Lan, Z. Xu, D. Qiu, L. Peng, Investigation and optimization of the ultra-thin metallic bipolar plate multi-stage forming for proton exchange membrane fuel cell, Journal of Power Sources, 484 (2021) 229298.
[8] H. Talebi-Ghadikolaee, M. Elyasi, M.J. Mirnia, Investigation of failure during rubber pad forming of metallic bipolar plates, Thin-Walled Structures, 150 (2020) 106671.
[9] V. Modanloo, V. Alimirzaloo, M. Elyasi, Optimal design of stamping process for fabrication of titanium bipolar plates using the integration of finite element and response surface methods, Arabian Journal for Science and Engineering, 45(2) (2020) 1097-1107.
[10] M.M. Barzegari, F.A. Khatir, Study of thickness distribution and dimensional accuracy of stamped metallic bipolar plates, International Journal of Hydrogen Energy, 44(59) (2019) 31360-31371.
[11] Q. Hu, D. Zhang, H. Fu, K. Huang, Investigation of stamping process of metallic bipolar plates in PEM fuel cell—Numerical simulation and experiments, International Journal of Hydrogen Energy, 39(25) (2014) 13770-13776.
[12] A. Bauer, S. Hдrtel, B. Awiszus, Manufacturing of metallic bipolar plate channels by rolling, Journal of Manufacturing and Materials Processing, 3(2) (2019) 48.
[13] M. Elyasi, H.T. Ghadikolaee, M. Hosseinzadeh, Fabrication of metallic bipolar plates in PEM fuel cell using semi-stamp rubber forming process, The International Journal of Advanced Manufacturing Technology, 92(1) (2017) 765-776.
[14] H.T. Ghadikolaee, M. Elyasi, F.A. Khatir, M. Hosseinzadeh, Experimental investigation of Fracture in rubber pad forming of bipolar plate’s micro channels, Procedia engineering, 207 (2017) 1647-1652.
[15] F.A. Khatir, M. Elyasi, H.T. Ghadikolaee, M. Hosseinzadeh, Evaluation of effective parameters on stamping of metallic bipolar plates, Procedia Engineering, 183 (2017) 322-329.
[16] M. Elyasi, H.T. Ghadikolaee, M. Hosseinzadeh, Investigation of dimensional accuracy in forming of metallic bipolar plates with serpentine flow field, The International Journal of Advanced Manufacturing Technology, 96(1) (2018) 1045-1060.
[17] V. Modanloo, H. Talebi-Ghadikolaee, V. Alimirzaloo, M. Elyasi, Fracture prediction in the stamping of titanium bipolar plate for PEM fuel cells, International Journal of Hydrogen Energy, 46(7) (2021) 5729-5739.
[18] F.A. Khatir, M. Barzegari, H. Talebi-Ghadikolaee, S. Seddighi, Integration of design of experiment and finite element method for the study of geometrical parameters in metallic bipolar plates for PEMFCs, International Journal of Hydrogen Energy, 46(79) (2021) 39469-39482.
[19] H. Talebi-Ghadikolaee, M. Elyasi, S. Shahgaldi, S. Seddighi, M.M. Kasaei, L.F. da Silva, The Effect of Rubber Hardness on the Channel Depth of the Metallic Bipolar Plates Fabricated by Rubber Pad Forming, in:  Materials Design and Applications IV, Springer, 2023, pp. 123-133.
[20] H. Talebi-Ghadikolaee, M.M. Barzegari, S. Seddighi, Investigation of deformation mechanics and forming limit of thin-walled metallic bipolar plates, International Journal of Hydrogen Energy,  (2022).
[21] C.-K. Jin, C.-G. Kang, A comparative study on the formability of aluminum bipolar plate with channels using indirect squeeze casting and stamping, International Journal of Precision Engineering and Manufacturing, 16(7) (2015) 1233-1238.
[22] M.G. Jung, Y.P. Jeon, C.G. Kang, Metallic Bipolar Plate Fabrication Process of Fuel Cell by Rubber Pad Forming and its Performance Evaluation, in:  Key Engineering Materials, Trans Tech Publ, 2013, pp. 310-313.
[23] H. Talebi-Ghadikolaee, F. Ahmadi Khatir, S. Seddighi, Numerical-experimental study on the thickness distribution of metallic bipolar plates for PEM fuel cells, Iranian Journal of Hydrogen & Fuel Cell, 9(1) (2022) 1-18.
[24] V. Modanloo, V. Alimirzaloo, M. Elyasi, Manufacturing of titanium bipolar plates using warm stamping process, Arabian Journal for Science and Engineering, 45(11) (2020) 9661-9667.